Search results

as in the title peeps, cheers, ollie

Evening all, Change has bought on alot of things recently and a new job job is one, hence the reason to put my car up due to needing a commuter. Spec is as follows, and not interested in selling or splitting. Pics here throughout the build (page 5 onwards are the most relevant)...

Evening all, MOT tomorrow and lost my bloomin abs relay. is there anything i can do to get the light off on the dash tomorrow morning? Cheers, ollie

Evening / early morning all, Thought I'd post up a few noises I'm getting. Certanly isn't causing any reduction in peformance but doing my head in nontheless. The first is a creaking sound. Happens just after pull off and sound like something tapping on the passenger footwell (nearest the...

Time to get the old girl breathing, I'm after a 3 inch turbo back system ideally. If I can't get one on here I'll have to get one custom made, Cheers, Ollie

as in the title, my uprated one is cracked and leaking.

checked the pressure yesterday and its not changing with my 044 pump noise however it seems a bit high. ~3.5 bar with the vacuum off and just under 3 with the vacuum on. vacuum removed: http://www.youtube.com/watch?v=pAHUEQ7-pPU vacuum on: http://www.youtube.com/watch?v=CwXEa3z64Io needle is a...

Afternoon all, Just thought i`d share this experience with you lot, and mabe you could check your intake system if you don`t have access to a wideband sensor. I`ve done a fair few changes to the intake / fuel system so i wanted to see if my air fuel ratio`s were still ok. Checked them and found...

Hi all, Please find my issue below: http://www.youtube.com/watch?v=fXIaBYicXD4 Power input to the pump is constant along with my AFR`s with them not changing inline with the pitch change on the pump. Setup is i have another 044 in the tank, feeding the swirl pot, then the other 044 being fed...

Adjustable FPR with gauge As in the title people. 8mm inlet preferred. Just a long shot before I order one

Standard or walbro, in good working order, cheers, ollie

Afternoon, i`m going to fit in a full cut off switch as seen here: these cut the ignition and battery so the engine actually "stops". wiring is here: http://www.holden.co.uk/productimagesWD/020_011.jpg anyone had a dig at wiring one up before? hardly had any experience with the electical...

before i go buy a spanker, is anyone selling a good one? cheers, ollie

as in the title guys, cheers, ollie

Hi all, Now i`ve got my cage fitted i`ve had to remove the sun visors. Out driving the other day i got blinded and would have been stuffed without my sunglasses. My window has a fairly deep standard tinted area as Has anyone toyed with fitting a functional sun stip? (just to blend in with...

Evening all, I`m after this bush that goes under the gearstick. I have a bad amount of up and down movement in my stick. This is the part i`m after: Part 34110G on the drawing below. Comes in two halves. Clearly want one with no up/down movement in the stick it came from. They`re on back order...

Afternoon all, Been looking at adjusting my clutch biting point in line with the owners manual as i`ve now got a "non worn through" clutch fork: http://www.gtirworkshopmanual.com/default.aspx?v=1265 and http://www.gtirworkshopmanual.com/default.aspx?v=1266 This says adjust so there`s 1-3mm...

Evening all, Anyone ever come across this before? I`m getting my rb box (used to be rich from redlines) ready for installation and noticed an end case bolt was missing. I thought i`d take one out of a box i`ve had for ages (stripped 3rd off bob) and found that the diameter and thread of the...

All, as in the title, cheers, ollie

Evening all, On the clutch fork sticking out of the box, if i push mine it rattles when not under slight preload. Shall i throw a new release bearing on when i change my box again or is this normal when not under slight preload? Cheers homies, ollie