Search results

  1. keastygtir

    Mine for sale

    see link for full details =AZWq3ZMD9j9r_xv5bkq4NKhAZOyx-HUw1bn-CH-zjfLRjHT9VVE_7a7ScF8C958eV6_Zcd_nkkoqbhZrPuyf4HHZwNH4FFOktEGb2f_UxHGovORAqslyYf5ByPdDsY7LSZr57vnw9p_4Ke970kBu_jDgBh9BCkCztCIdPJDoPWUSSg&__tn__=-UK-R']https://www.facebook.com/groups/1267363723290305/permalink/4346692518690728 Thanks
  2. keastygtir

    Shocks and springs experiment

    Hi all Putting this up for info. I never really wanted coilover suspension for my car but the lack of alternatives meant that I ended up getting some. I wont go over some of the draw backs of cheaper coilover setups as it been well covered, but for the use and type of roads I use the car on my...
  3. keastygtir

    Bleed Nipple 3062380E00

    Anyone know the thread size for these please?
  4. keastygtir

    Front pipe required, mongoose etc.

    as above
  5. keastygtir

    Gear selector road bush

    Hi all I am having some issues selecting first and second gear at low speeds. Sometimes its fine sometimes a bit notchy. From looking into it I can see there is some play in the linkage bush at the end of the rod. Also with the gear stick in neutral pushing to the right it springs back nice but...
  6. keastygtir

    Transmission shove

    Hi all With the car being back on the road I am working through some of the little issues you get after the car has been off the road for so long! I have a question regarding the transmission. I am getting a little shunting whilst on slow downshifts. I assume this is to do with the new clutch...
  7. keastygtir

    Front wishbone Caster bush bolt

    Front wishbone Caster bush bolt has stripped its thread. I assume it is a captive nut inside the chassis. I plan to drill out to m14 and tap, using a new bolt. Would that be the best approach? Any advice welcomed.
  8. keastygtir

    Bonnet vent gasket

    Hi My main vent came back from the body shop without the gasket, he said it fell to bits when removed. Nissan dont have them and I dont know exactly what they look like to make a replacement. Anybody have any suggestions?
  9. keastygtir

    Holes in sills

    Would anybody be kind enough to give me some measurements of the side skirt and trim slots in the sills? I need to put new ones in my new sills. Thanks
  10. keastygtir

    Trim splash cover confusion

    Hi I am a little unsure of where this panel is located on the car. The part number looks like its fits the front left under the wing but I an not sure. Any help welcome. Thanks
  11. keastygtir

    Help identifying some parts and locations

    Hi Everyone. Could someone post a picture up of the boot with all the carpet panels etc installed? I am rebuilding mine and I am stuck on a few bits. Also the front lower seat belt anchors would be appreciated. Thanks
  12. keastygtir

    Anyone run a 195/55/15 tyre?

    Instead of a 195/50/15?
  13. keastygtir

    Intrax suspension available

    Hi I emailed any inquiry to Intrax regarding suspension solutions and thought I would share the outcome. Hello Kevin, Thanks for your interest in our products. Underneath I’ll explain all the systems we have available (in Europe the Pulsar is called Sunni). For fast road use all our...
  14. keastygtir

    removing rear window upper trims

    Hi All Is there a knack to it? I have removed one set and broke a few of the clips. They were proper stuck in there! Thanks
  15. keastygtir

    strange gauge behaviour

    Hi All Ran the car up today and noticed that if I put in the interior fan on it makes the dash gauges jump up and change their readings. Anyone had this before?
  16. keastygtir

    Bed in rings

    Hi Guys Now that my engine is in the car and running ok. Does it matter how long I take to bed in the rings? Thanks Kev
  17. keastygtir

    replacement arch trims

    Hi everyone I am coming toward the time when I am starting to plan the putting back together of my car and fitting dome of the trim items. The arch trims on mine seemed to be a starting point for a lot of the rust found around the rear arches and front wings. To counter this I am having some...
  18. keastygtir

    Message for MAD

    Please can you PM me. Thanks Kev
  19. keastygtir

    Clutch bite point

    Hi Guys Tested moving the car tonight, the clutch engagement seems quite low to the floor. I have a new CC stage 3 clutch and re-inforced fork, new slave cylinder. I have bled the system. I have also noticed the rod from the slave cylinder rattles against the bracket slightly when clutch is...
  20. keastygtir

    8 Bar Oils pressure

    Hi Guys As per my build thread I stated the car last night. Everything seems well but the oil pressure was 8 bar and dropped a bit a running for few minutes. Does this seem normal?
Top