Search results

  1. bensmith907

    Hose Size FPR-Map sensor-manifold

    Hey there sorry to have to ask this but I'm looking at replacing my boost hose work for the fuel pressure regulator/map sensor/manifold line/boost controller. Does anyone know what diameter I should use? Thanks, I would check on the car myself if I was anywhere near it moment. Ben
  2. bensmith907

    oil leak advice

    I've got an oil leak coming from around the oil pump area on my newly built engine. I'm not 100% but I'm sure its coming from the cylinder portion on top of the pump. Has anyone had this sort of problem before? I have gone over the workshop manual for fitting the pump and it states not to put...
  3. bensmith907

    dyno run disappointmenmt

    Have a look at this- Just at a dyno getting the R checked out this is the graph produced- The guy running it says the power just drops off then comes back Running a mines ecu, Forged pistons, Cosworth head gasket Greddy profec b 2 boost ctrl Set at 40% (1.15bar) Gain 30 Set gain 40 Standard...
  4. bensmith907

    Pull the other one!

    This is a crank pully puller question-I've read a few times about not using a cheap Halfrauds puller to get the crank pully off, but if not the claw style one what is everyone using? Links or if anyone is selling would be useful
  5. bensmith907

    is this right? carbon canister hose..

    A friend of mine is fixing his GTiR and finds a hose hanging about the passenger wheel arch. He calls me up to see where it fits to but when I look at mine its exactly the same. Now I'm not a big believer in engineering by comparison I I thought I would get some good gen from the forum...
  6. bensmith907

    What Induction Kit is Everyone Using?

    I was just wondering what Filter everyone is using? I was reading an article which has tempted me to get a Powertec filter (the metal mesh one) they done a test that showed how restrictive all the big brands and this came out shining.
  7. bensmith907

    another hesitation thread

    I know this forum isn't short on this topic but I want to be sure that I'm getting the right advice. The car has started hesitating from about 2-3.5k. Ill put my foot down and the noise from the exhaust goes up quite loud but with no real acceleration to go with it. I'm pretty sure its not a...
  8. bensmith907

    valve shims

    Would someone be willing to cut us up some feeler gauges to put under my valve caps as a tempory measure. I need 16x 0.005" and 1x0.010" I will obviously cover the costs of the gauges and postage Thanks!
  9. bensmith907

    WANTED_ aux/secondary air hose kit

    as the title suggests, im looking for a good condition or new hose kit. no cheap e-bay crap thanks Ben
  10. bensmith907

    Anyone got any standard wheels?

    As title suggests let me know if you have any I can buy from you? Thanks, Ben
  11. bensmith907

    WANTED- Turbo Actuator ASAP t28

    What have you got? must be next day delivery. Please PM me so that I get an alert to my phone or text 07795055304 Thanks, Ben
  12. bensmith907

    Rubber Boot gear Linkage

    Anyone have a good one, know a good supplier or know the nissan part number. Its the one under the car close to the gear linkage disconnect bolt. mine is split and Ive been told it'll be a MOT failure Thanks, Ben
  13. bensmith907

    WANTED! Oz alloy wheel

    One of my wheels is buckled! Not sure what the name of this wheel is- the words 'OZ, rally and compomotive' seem to bring up simular ones on e bay but 100x4 are rare and its hard to know what wheel is suitable for the GTI-R. Does anyone have a single one or two they want to sell, 15inch...
  14. bensmith907

    can I fit willwood midilights

    I've just been offered some willwoods midilights?? Are these compatible with the pulsar? I imagine it'll be some kind of bracket required? Thanks, Ben
  15. bensmith907

    Wanted! Uprated Head Gasket 86mm

    as the title suggests... bottom end has now been built and the plan was to buy a 87mm cosworth gasket from Henners who was doing a bulk buy on the modifiers forum. this appears to have faded out as I cant get a reply from him. I understand the only time you buy these is if you need them...
  16. bensmith907

    Suspension, creeking and knocking

    Sometimes I swear im the unluckyiest Pulsar owner there is- I have a suspension problem now. when I accelerate and brake there's a knocking from the driverside footwell and when I move in very slow traffic there is a creek when the wheels rotate. Ive looked at all the bushings on the lower...
  17. bensmith907

    Wanted- Gear Knob

    as title, would prefer standard but really the important thing is that it screws on to the gear stick. any condition as long as its still in one piece! Im getting fed up with the one I currently have coming off in my hand all the time! also if anyone has a good condition gaiter going for a...
  18. bensmith907

    clutch arm dust cover

    Any one know where I can get a dust/gaiter cover for the hole for the clutch arm? I'm sure I've seen them on ebay but can't for the life of me find them
  19. bensmith907

    Bens Engine Rebuild

    I had a post on here a while back with smoke from the exhaust and poor compression on #3 cylinder. smoke appears to be the turbo bearing. on the compression test I got the results 146, 139, 100, 135- so all round- not very good pressures. I did a wet compression test on number 3 and the...
  20. bensmith907

    Oil from Block

    Hello all, As usual I come with problems. I have fitted a new engine whist I rebuild the old one. but the new engine has a real oil drinking problem. when I go on a long drive the right side of my car becomes soaked in Oil. it appears to be coming from the mounting point indicated on the...
Top