Search results

I am looking a crank shaft pulley for my gtir

the standard fuel rail is fine. just get the ones with the yellow top they are 11mm

I agree with the above statement , just to add a little more info to that you will need to use the stiffest supertech valve springs u can find and retainers with oem sr16ve cams u will be able to rev this engine to 1100-1200rpm you will also need pistons with valve relieve cut outs in them or...

better you do what I did go with a aem standalone and get rid of the maf all togetherjust use a map sensor and a iat sensor and 1000 cc injector dynamics injectors and start tuning

damn !!!!!!!!! and i see some guys with evo's and wrx's doing it . good thing i asked first lol

can a gtir be tuned on a 2wd rolling road? ie by disconnecting the propshaft? because now there is finally a dyno in my country but its for 2wd vehicles so i was wondering if it can be used to dail in my engine

i have both a gtir and a gti and the front discs and calipers and rear disks and calipers are different on both cars

what kind of ecu are you using? i had that same problem when i first installed my aem standalone. it made my iac valve click even when i took out the key from the ignition. it was getting a constant 12v power. so i had to swap the pins in the harness for it to stop. so first check the 2 10mm...

5) Wiring accessories to the EMS: Please follow this suggested wiring diagram when adding accessories such as UEGO gauges, MAP sensors, IAT sensors, or switches for use with the EMS. Note that wire polarity is not important for the Air Temperature sensor. +5V Sensor Power Switched Input 41...

where can i get a complete ecu pin out for the gtir. which tell me what each pin is for? so i want to know what every pin is for so i can see if i have to swap pins to fit the aem ems there is the one have...

yes i do. i have an aem 30-6600 series 2 ems.

i want to install an aem 5 bar map sensor on my gtir can i use the 3 wires that goes to the stock boost sensor? and i have installed an aem (ait sensor) air inlet temperature sensor. where do i find these 2 wires on the ecu harness first wire is to sensor ground and the next wire goes directly...

hi i have an issue with these rubber plugs on the intake manifold that are next to the injectors they keep blowing off how can i solve this problem?

http://www.ebay.co.uk/itm/Genuine-Nissan-Pulsar-GTIR-Crank-/181473034027?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item2a40a2bf2b

i have in 8.5:1 compression forged cp pistons and had no issues with them for the past 5 years plus i use thhttp://www.ebay.com/itm/Cometic-C4543-051-Head-Gasket-Nissan-SR20DET-Pulsar-GTiR-87-5mm-x-1-3mm-MLS-AWD-/181371904139?pt=Motors_Car_Truck_Parts_Accessories&hash=item2a3a9ba08b&vxp=mtris...

http://www.amazon.com/AEM-30-8762-CAS-Trigger-Disc/dp/B007ZGEKFS/ref=sr_1_3?ie=UTF8&qid=1404005909&sr=8-3&keywords=aem+trigger+disc

i have this aem http://www.amazon.com/AEM-30-6600-Series-Management-Infiniti/dp/B003V94GP2/ref=sr_1_1?ie=UTF8&qid=1404005599&sr=8-1&keywords=aem+30-6600 and now my R is a beast

water hoses at back of the engine. det sensor, starter motor brushes, water pump,crankshaft seals check the clutch and release bearing

http://www.ebay.com/itm/Precision-54mm-MFS-Turbo-5454E-Journal-Bearing-T3-T4-495hp-63-A-R-4-Bolt-5454-/270996797715?pt=Motors_Car_Truck_Parts_Accessories&hash=item3f18aaf913&vxp=mtr

how do i get photos load on here?