Search results

  1. A

    3-4 fork rod

    Does anybody know if there should be a pin in a 3-4 fork rod hole between locking balls? Manual shows that there should be one but my box is missing it or am i wrong??? -Thanks
  2. A

    W: aircon

    Basically i need everything except pump bracket and inside evap rad. If anybody lying and want's to get rid of it i'll happily take it.
  3. A

    So, who is watching in russian???

    Guess the site had been hacked. Unless there's serious russian lovers. :sweatsmile:
  4. A

    Crankshaft

    After one
  5. A

    Os giken's hub

    anybody got one spare or lying around before i go shopping japan? Dampenend twin center hub
  6. A

    Head gasket/comp ratio

    Rough idea for people who are deciding on new head gasket and wonder about comp ratio(unskimmed head&block), Stock ratio is 8.3:1 88.0mm Gasket 86.0mm Piston 87.0mm Piston 0.6mm____________9.2:1___________9.0:1 1.0mm____________8.9:1___________8.7:1 1.2mm____________8.7:1___________8.6:1...
  7. A

    OS Giken

    Is it possible to use NS062-BF6 Silvia S15 TR2CD Dampened Twin Plate instead of a NS261-BH6 R2CD? If i open up flywheel holes. Reason i'm asking is that i could get one cheap.
  8. A

    Hks twin plate

    As per title, what is it like. Heavy on the pedal or not, noisy, parts, daily commute? As I gather it's discontinued but assume replacement parts can be bought.
  9. A

    Head without cam caps

    Have a guy here with 2 heads for sale but no cam caps, any point buying them off him?
  10. A

    Gearbox internals

    I'm in need of some parts for gearbox. I need a oil gutter and interlocking pin for middle rod. For transfere box i need the plastic cog for spido. Preferably in london area, i'll be visiting your lovely island from 11nov till 14nov -Thanks
  11. A

    Gear locker got stuck!

    It happened when the car was on dyno, 3rd and 4th gear locker got stuck in 4th. Just got the injectors set up so there wasn't even heavy load on the box. Sufficient amount of oil was in the box as well. It used to be light metal color. Any ideas???
  12. A

    Which way?

    Which way release bearings retainers should be on? Manual says that you should pay attention which way the are but which way is correct way???
  13. A

    OEM head gasket

    How much Bhp can/will a OEM head gasket cope with? Somewhere was a figure of 320 Bhp or so, is that right or bollocks??
  14. A

    Is it worth it,fmic?

    Was thinking if it's worth to do same side pipe entry and exit fmic. It would eliminate turbo to cooler pipe which travels over exhaust many, just turn the turbos cold side 180deg and run the pipe to the same side from which the pipe runs in to the inlet many??? But then i was thinking if air...
  15. A

    w: few parts

    hi, i need input shaft, and speedo cog
  16. A

    Another gearbox problem

    Right so, after a short drive(mile or so) i cant select gears 1 and 2! the stick won't just move to your left for selection of the gears??? third, fourth, fifth and reverse all go in fine???
  17. A

    Coolant/gasket problem

    Right so. After a few months i took my car out again for a day on the ice lake. Noticed two broblems: Pressure in the rad and weebit smoke/ coolant from exhaust only when it gets hoter than usually. And it does heat up really quickly. I use cometic head gasket, upon quick search i found that...
  18. A

    gearbox parts

    I need new input shaft + the helix cog wich is behind the reverse gear
  19. A

    clutch plate

    Does anyone know from head how many teeth is on the gearbog shaft(the stick on witch the clucth plate sits)?
  20. A

    Oil filter seal

    Odd thing happened yesterday, my R was in the garage and mate of mine changed oil on it and changed the oil filter as well. Later that night he went for a spin and came back walking, LOL. He said that the oil pressure dropped and he pulled aside the road and switched it of. In the morning he...
Top