Search results

  1. S

    can't send messages

    I was at my maximum message limit, so saved half a dozen to a new folder and deleted the rest. Now I still can't send messages as it says I'm still exceding my limit. How do I fix it?
  2. S

    Crank Pulley Wanted

    Either an excellent condition standard one or a non Forge aftermarket alloy one.
  3. S

    Weird mapping issues with blow through MAF

    I switched my MAF for a hardpipe blow through one and it seemed to run ok, but as it can effect the mixture I decided to have it remapped to suit.Also had a Bosch 044 and new fuel relay fitted and cam timing set up. Anyway, just spoke to the mapper and he says it's doing some strange things...
  4. S

    Federal RSR tyres

    Anyone used these?Am thinking of getting a set.It seems thy are in between a road trye and a semi slick, not too far behind an 888 on track but still ok for the road, even in the rain.Obviously the wear won't be fantastic but I'm not too fussed as my annual mileage is tiny anyway. My thinking...
  5. S

    Anyone retrimmed the back of car?

    ..after removing the seats?Thnking of using felt or alcantara or something but don't really know where to start.Am presuming you use some spray glue but not sure how it will go on in the raised/depresed areas as shapes like that are normally pressure formed. Anyone got any tips on how to go...
  6. S

    Wanted: Bosch 044 fuel pump

    Anyone have a genuine Bosch 044 pump?Or know where I can get a new one for a decent price?
  7. S

    Fuel swirl pot, external pump and fittings

    Am after a full setup to get rid of the fuel surge these cars can suffer from.What have you got(with pics please).
  8. S

    Dialling cams in and mapping

    I am looking to get my car mapped again soonish by Ed at Fusion, but want my cams dialled in which are currently set at 0.Basic spec is forged pistons, steel rods, head and crank studs, 1mm steel headgasket, mild p&p of head, double valve springs, rocker stoppers, tomei 260 cams everything...
  9. S

    Rear diff in GWO

    Mine is a bit clunky lately and looking to change it at the same time I have the STR motorsport gearbox collar fitted.Needs to be in good nick and not too far away(I am in Chesterfield).
  10. S

    Wanted:Standard drivers seat

    Just want a cheap drivers seat, condition not important as I am only really after the rails to modify to fit my bucket seat to.I don't want to wreck my own seat if it doesn't work out. The problem is, when I fit the seat-cobra suzuka on cobra subframe the seat is too high and when I have my...
  11. S

    Car mapped today

    Took it the long drive down to Ed's at Fusion and after a bit of tinkering it was mapped on Surrey RR.As usual for me nothing went smoothly but at least it was no longer holding back at the topend like last time.Am 99% sure it was down to a poor air feed for the filter and the stepping down from...
  12. S

    What size banjo bolt for oil feed to turbo?

    Look slike my new turbo has to come off due to a damaged diaphragm on the actuator.Its a gt3071 with the standard 0.040" restrictor in it but have notice a little puff of smoke when changing gear when its boosting, so might have to fit an extra restrictor as well.I'm thinking it would be easiest...
  13. S

    Overboosting

    Since I had the rest of my exhaust made in 3" pipe, the gt3071 has spooled much faster even on part throttle.My problem is now I've done a fair few miles on it, its overboosting.The new forge actuator is set at 1.2 bar and I am sure it opened at this on the old mongoose but now the boost shoots...
  14. S

    Wanted: 3" Exhaust

    Needed from downpipe back(already have a Janspeed downpipe), must be nice and quiet when pootling about, not worried about it barking when giving it some beans. Its a long shot but thought I'd check before having one made.
  15. S

    What else should I order?

    Just received my GT3071 from Turbo Dynamics and the things I can think of to order to fit it are: Silicon for outlet mandrel 90 degree bend (to couple to turbo outlet and Forge i/c pipework) silicone coupler 76mm>71mm silicone reducer for turbo inlet(have 3" inlet pipe and turbo is 2.75"...
  16. S

    Anyone got AET's email....

    that actually works/that they answer? AET one keeps getting bounced back(sales@aet-turbos.co.uk) as it doesn not exist yet its the one I got from their website.
  17. S

    What will my CR be?

    I have 87mm tomei pistons, PAR rods(so presume still the standard 86mm) and a 1mm tomei hg.Assuming an average skim for the rebuild what would my CR be roughly?I'm thinking high 8's?
  18. S

    MAF and airflow to calculate power

    I sometimes have a read on the Seat forums and through their VAGCOM they can monitor allsorts of info, including the flow of the MAF in g/s(I presume grammes per second).Anyone ever used anything like this on our cars?I am sure one of the more boffin types could knock something up to provide a...
  19. S

    Anyone with a Turbodynamics MD214?

    Are the actuator dimensions/rod length the same as standard?Is it the straight rod or bend rod type(assuming its straight, never seen the bent type).Am looking to get a stronger one from either Forge or Td and cannot check the one on the car atm as car won't start and its parked in my garage...
  20. S

    Wanted 1.2 bar actuator

    To fit standard turbo housing.I don't want one you "think" is uprated as I might end up with a lemon.Let me know what you have :).
Top